View Categories

Manual TD01Z

0:00 3:22

Descarga de la aplicación #

Escanee el código QR o haga clic en el botón para descargar. “Tuya Inteligente” aplicación

Aplicación inteligente Tuya
Haz clic en Descargar

Características #

● This product is made by 2.4GHz RF wireless transmitting technology with low consumption and strong ability to resist signal loss.
● Adopted standard Zigbee 3.0 protocol.
● Support 2.4G remote control.
● Support ” Tuya ” App control (Zigbee 3.0 gateway is required)
● Amazon Alexa, Philips Hue, Yandex Stetion, Home Assistant control.
● 1-channel output, Max 1.5A.
● Trailing edge phase-cut dimming.
● Supports minimum brightness setting.
● Built-in temperature detection switch.

Parámetros #

Modelo No:TD01Z
Input / Output:AC100-240V   50/60Hz
Corriente de salida:Max 1.5A
Output Power:150W@110V, 300W@220V
Control Signal:Zigbee 3.0 + 2.4G + PUSH
RF Control Distance:30m
Zigbee Distance:50 metros
IP Rate:IP20
Working Temp.:-20~45°C

Diagrama de conexión #

Atención

1. Please cut off power before wiring device.
2. Please check the voltage of power before connecting.
3. It’s high voltage product which need to wire ground line.

PUSH Dimming #

Short press push switch : Turn on/off light

Long press push switch:

  • Stepless dimming brightness
  • Long press double times to increase or decrease brightness

Atención #

  1. One push switch can connect with various dimmer,please long press push switch 20 seconds to keep all lights in the same brightness.
  2. One push switch only connect with 25 dimmers (max)
  3. The cable of push switch can not be over 20m

Detalles de la aplicación #

1. Works with following Zigbee 3.0 hubs #

2. Device Into Zigbee Pairing Mode #

Method 1

Long press “ LINK ” 3 seconds.

Method 2

Long press “ Push Switch ” 30 seconds.

Add to Amazon Echo (Alexa) #

Echo with built-in Zigbee

1. Put device into Zigbee pairing mode.
2. Say to Amazon ECHO “Alexa, Discover devices” .
3. Wait for a while to discover device, Voice control is activated.

Add to Philips Hue #

Philips Hue Bridge is required

1. Put device into Zigbee pairing mode.
2. Open “Philips Hue” App to click “SETTINGS” and click “Lights”.
3. Click “+” on the top of right corner.
4. Click “Search”.
5. Click “Start configuration”, Follow the app instruction to complete configuration.

Add to Home Assistant #

Zigbee 3.0 Coordinator is required

1. Put device into Zigbee pairing mode.
2. Open Home Assistant app and go to “Zigbee2MQTT”.
3. Click “Ξ”.
4. Click “Permit join (All)” .
5. Wait for the device to connect.
6. Added successfully.

#

Tuya Zigbee 3.0 gateway is required

1. Put device into Zigbee pairing mode.
2. Open “Tuya” APP to click Zigbee gateway, then click “Zigbee”.
3. Click “Add device”.
4. Added successfully.

Control remoto 2.4G #

Código de enlace (2 soluciones diferentes) #

Method 1

Prensa breve “ LINK ” 1 time, short press “ I ” on the remote 3 times within 3 seconds.

Method 2

Press “ Push switch ” and turn on light, short press “ I ” on the remote 3 times within 3 seconds.

Prensa breve “ I ” 3 times within 3 seconds. Linking code is done if the lights flashes 3 times slowly.

 Don’t use “Master ON” to link code. You only can link lights into one zone on one remote.

Código de limpieza (2 soluciones diferentes) #

Method 1

Prensa breve “ LINK ” 1 time, short press “ I ” on the remote 3 times within 3 seconds.

Method 2

Press “ Push switch ” and turn on light, short press “ I ” on the remote 3 times within 3 seconds.

Prensa breve “ I ” 5 times within 3 seconds.

Cleaning code is done if the lights flashes 6 times quickly.

Mini brillo #

Preventing the light is off or flashing while dimming it to lower brightness.

Method 1

Short press “set” continuously to set up 10 kinds of brightness ( 1%, 5%, 10%, 15%, 20%, 25%, 30%, 35%, 40%, 50%).

       Method 2

  1. Mantener pulsado “ ”" o "“ ” in group zone 6 seconds until light flashes one time.
  2. Prensa breve “ ”" o "“ ” in group zone to set up 10 kinds of brightness.

Tiempo de encendido/apagado #

El estado de la luz cambia gradualmente (el tiempo predeterminado de fábrica es de 0,5 s).

1,5 s: Presione brevemente “ON” 1 vez y presione brevemente “OFF” 5 veces en 3 segundos; la configuración se realizará cuando la luz parpadee 2 veces lentamente.

0,5 s: Presione brevemente “OFF” 1 vez y presione brevemente “ON” 5 veces en 3 segundos; la configuración se realizará cuando la luz parpadee 2 veces rápidamente.

ON/OFF Dimming mode #

Shut down dimming mode ( activate ON/OFF mode) #

Mantener pulsado “SET” 10 seconds, dimming mode is shut down while indicator flashes 3 times slowly.

Activate dimming mode #

Mantener pulsado “SET” 10 seconds, dimming mode is activated while indicator flashes 3 times quickly.

Atención #

  1. Por favor, desconecte la alimentación antes de conectar el dispositivo.
  2. Please check the voltage of power before connecting.
  3. No lo desmontes si no eres un experto.
  4. No lo utilice en zonas metálicas o magnéticas.
Scroll al inicio