Categorieën bekijken

TD01Z Manual

App downloaden #

Scan de QR-code of klik op de knop om te downloaden “Tuya Smart” app

Tuya Smart-app
Klik op ‘Downloaden’

Kenmerken #

● This product is made by 2.4GHz RF wireless transmitting technology with low consumption and strong ability to resist signal loss.
● Adopted standard Zigbee 3.0 protocol.
● Support 2.4G remote control.
● Support ” Tuya ” App control (Zigbee 3.0 gateway is required)
● Amazon Alexa, Philips Hue, Yandex Stetion, Home Assistant control.
● 1-channel output, Max 1.5A.
● Trailing edge phase-cut dimming.
● Supports minimum brightness setting.
● Built-in temperature detection switch.

Parameters #

Modelnr:TD01Z
Input / Output:AC100-240V   50/60Hz
Output Current:Max 1.5A
Output Power:150W@110V, 300W@220V
Control Signal:Zigbee 3.0 + 2.4G + PUSH
RF Control Distance:30m
Zigbee Distance:50m
IP Rate:IP20
Working Temp.:-20 tot 45 °C

Aansluitschema #

Let op

1. Please cut off power before wiring device.
2. Please check the voltage of power before connecting.
3. It’s high voltage product which need to wire ground line.

PUSH Dimming #

Short press push switch : Turn on/off light

Long press push switch:

  • Stepless dimming brightness
  • Long press double times to increase or decrease brightness

Let op #

  1. One push switch can connect with various dimmer,please long press push switch 20 seconds to keep all lights in the same brightness.
  2. One push switch only connect with 25 dimmers (max)
  3. The cable of push switch can not be over 20m

App-details #

1. Werkt met de volgende Zigbee 3.0-hubs #

2. Het apparaat in de Zigbee-koppelingsmodus zetten #

Method 1

Long press “ LINK ” 3 seconds.

Method 2

Long press “ Push Switch ” 30 seconds.

Toevoegen aan Amazon Echo (Alexa) #

Echo met ingebouwde Zigbee

1. Zet het apparaat in de Zigbee-koppelingsmodus.
2. Zeg tegen Amazon Echo: “Alexa, zoek apparaten”. .
3. Wacht even tot het apparaat wordt gedetecteerd; de spraakbesturing is nu geactiveerd.

Toevoegen aan Philips Hue #

De Philips Hue Bridge is vereist

1. Zet het apparaat in de Zigbee-koppelingsmodus.
2. Open de app “Philips Hue”, tik op “INSTELLINGEN” en tik vervolgens op “Lampen”.
3. Klik op het “+”-teken rechtsboven in de hoek.
4. Klik op “Zoeken”.
5. Klik op “Configuratie starten” en volg de instructies in de app om de configuratie te voltooien.

Toevoegen aan Home Assistant #

Een Zigbee 3.0-coördinator is vereist

1. Zet het apparaat in de Zigbee-koppelingsmodus.
2. Open de Home Assistant-app en ga naar “Zigbee2MQTT”.
3. Klik op “Ξ”.
4. Klik op “Deelname toestaan (Alle)”. .
5. Wacht tot het apparaat verbinding maakt.
6. Succesvol toegevoegd.

#

De Tuya Zigbee 3.0-gateway is vereist

1. Zet het apparaat in de Zigbee-koppelingsmodus.
2. Open de app “Tuya”, klik op de Zigbee-gateway en klik vervolgens op “Zigbee”.
3. Klik op “Apparaat toevoegen”.
4. Succesvol toegevoegd.

2,4 GHz-afstandsbediening #

Code koppelen (2 verschillende oplossingen) #

Method 1

Short press “ LINK ” 1 time, short press “ I ” on the remote 3 times within 3 seconds.

Method 2

Press “ Push switch ” and turn on light, short press “ I ” on the remote 3 times within 3 seconds.

Short press “ I ” 3 times within 3 seconds. Linking code is done if the lights flashes 3 times slowly.

 Don’t use “Master ON” to link code. You only can link lights into one zone on one remote.

Schoonmaakcode (2 verschillende oplossingen) #

Method 1

Short press “ LINK ” 1 time, short press “ I ” on the remote 3 times within 3 seconds.

Method 2

Press “ Push switch ” and turn on light, short press “ I ” on the remote 3 times within 3 seconds.

Short press “ I ” 5 times within 3 seconds.

Cleaning code is done if the lights flashes 6 times quickly.

Mini Brightness #

Preventing the light is off or flashing while dimming it to lower brightness.

Method 1

Short press “set” continuously to set up 10 kinds of brightness ( 1%, 5%, 10%, 15%, 20%, 25%, 30%, 35%, 40%, 50%).

       Method 2

  1. Long press “ ” or “ ” in group zone 6 seconds until light flashes one time.
  2. Short press “ ” or “ ” in group zone to set up 10 kinds of brightness.

ON/OFF Time #

The light status changes gradually (factory default time is 0.5s).

1.5s: Short press “ON” 1 times and short press “OFF” 5 times within 3 seconds, the setting is done once light flashes 2 times slowly.

0.5s: Short press “OFF” 1 times and short press “ON” 5 times within 3 seconds, the setting is done once light flashes 2 times quickly.

ON/OFF Dimming mode #

Shut down dimming mode ( activate ON/OFF mode) #

Long press “SET” 10 seconds, dimming mode is shut down while indicator flashes 3 times slowly.

Activate dimming mode #

Long press “SET” 10 seconds, dimming mode is activated while indicator flashes 3 times quickly.

Let op #

  1. Schakel de stroom uit voordat u het apparaat aansluit.
  2. Please check the voltage of power before connecting.
  3. Demonteer het apparaat niet als u hier geen ervaring mee hebt.
  4. Gebruik het niet in een omgeving met metaal of magnetische velden.
Scroll naar boven