Características #
- This product is made by 2.4GHz RF wireless transmitting technology with low consumption and strong ability to resist signal loss.
- Compatível com controle remoto 2.4G.
- 1-channel output, Max 1.5A.
- Trailing edge phase-cut dimming.
- Supports minimum brightness setting.
- Built-in temperature detection switch.
Parâmetros #
| Modelo n.º: | TD01 |
| Input / Output: | AC100-240V 50/60Hz |
| Output Current: | Max 1.5A |
| Output Power: | 150W@110V, 300W@220V |
| Control Signal: | 2.4G + PUSH |
| Control Distance: | 30m |
| IP Rate: | IP20 |
| Working Temp.: | -20~45°C |
Esquema de ligação #
Atenção
1. Please cut off power before wiring device.
2. Please check the voltage of power before connecting.
3. It’s high voltage product which need to wire ground line.
PUSH Dimming #
Short press push switch : Turn on/off light
Long press push switch:
- Stepless dimming brightness
- Long press double times to increase or decrease brightness
Atenção #
- One push switch can connect with various dimmer,please long press push switch 20 seconds to keep all lights in the same brightness.
- One push switch only connect with 25 dimmers (max)
- The cable of push switch can not be over 20m
Vinculação de código (2 soluções diferentes) #
Method 1
Pressionar "curto prazo"“ LINK ” 1 time, short press “ I ” on the remote 3 times within 3 seconds.
Method 2
Press “ Push switch ” and turn on light, short press “ I ” on the remote 3 times within 3 seconds.
Pressionar "curto prazo"“ I ” 3 times within 3 seconds. Linking code is done if the lights flashes 3 times slowly.
Não use “Master ON” para vincular o código. Você só pode vincular luzes a uma zona por controle remoto.
Código de limpeza (2 soluções diferentes) #
Method 1
Pressionar "curto prazo"“ LINK ” 1 time, short press “ I ” on the remote 3 times within 3 seconds.
Method 2
Press “ Push switch ” and turn on light, short press “ I ” on the remote 3 times within 3 seconds.
Pressionar "curto prazo"“ I ” 5 times within 3 seconds.
O código de limpeza é acionado se as luzes piscarem 6 vezes rapidamente.
Mini brilho #
Preventing the light is off or flashing while dimming it to lower brightness.
Method 1
Short press “set” continuously to set up 10 kinds of brightness ( 1%, 5%, 10%, 15%, 20%, 25%, 30%, 35%, 40%, 50%).
Method 2
- Pressione e segure “
”" ou "“ 
” in group zone 6 seconds until light flashes one time. - Pressionar "curto prazo"“ ”" ou "“ ” in group zone to set up 10 kinds of brightness.
ON/OFF Time #
The light status changes gradually (factory default time is 0.5s).
1.5s: Short press “ON” 1 times and short press “OFF” 5 times within 3 seconds, the setting is done once light flashes 2 times slowly.
0.5s: Short press “OFF” 1 times and short press “ON” 5 times within 3 seconds, the setting is done once light flashes 2 times quickly.
ON/OFF Dimming mode #
Shut down dimming mode ( activate ON/OFF mode) #
Pressione e segure “SET” 10 seconds, dimming mode is shut down while indicator flashes 3 times slowly.
Activate dimming mode #
Pressione e segure “SET” 10 seconds, dimming mode is activated while indicator flashes 3 times quickly.
Atenção #
- Por favor, desligue a energia antes de conectar o dispositivo.
- Please check the voltage of power before connecting.
- Não desmonte se você não for especialista.
- Não utilize em áreas metálicas ou magnéticas.
