View Categories

iM5V Manual

Features #

    • This product is made by 2.4G wireless transmitting technology with low consumption and strong ability to resist signal loss.
    • 5 kinds of output mode support 5 led strip (Single color/CCT/RGB/RGBW/RGB+CCT)
    • Support 2.4G remote control.
    • Built-in micro chip and support music rhythm

Parameters #

Model No.iM5V
InputDC12V-24V
Output6A/Channel
Total outputMax 12A
RF2.4GHz
Control distance30m
Working temperature-20~45°C
Product Size91*38.5*17mm (L*W*H)

controller dimensions diagram
controller interface diagram
  1. Input 1

  2. Input 2 (DC5521 Max 10A) 

  3. Indicator

  4. SET button

  5. Output

  6. Micro hole

Connection Diagram #

For single color led strip (short press “SET”–white indicator)

Single Color Connection Diagram

For dual white led strip (short press “SET”– yellow indicator)

CCT Connection Diagram

For RGB led strip (short press “SET”–red indicator)

RGB Connection Diagram

For RGBW led strip (short press “SET”–green indicator)

RGBW connection diagram

For RGB+CCT led strip (short press “SET”–blue indicator)

RGBCCT connection diagram

Output mode settings #

Short press (SET) continuously to select output mode, indicator displays different output modes as following diagram.

Indicator Output
White Single color
Yellow Dual white
Red RGB
Green RGBW
Blue RGB+CCT

Setting PWM frequency #

Long press “SET”until indicator flashes, short press “SET” continuously to select PWM frequency.

Lowest Flashing slowlyFlashing quicklyFastest
250Hz2KHz4KHz8KHz

PWM frequency (changing different frequency to solve the noise problem from power adapter).

  High frequency only support device with lower wattage, low frequency support device with higher wattage and have better dimming performance. Factory default PWM frequency is 4KHz.

2.4G Remote Control #

Linking code (2 different solution) #

Link description
Solution 1 #

Short press “SET” 1 time, short press “ I ” 3 times within 3 seconds

Link description
Solution 2 #

Power off and power on, short press “ I ” 3 times within 3 seconds

  Link is done if the light flashes 3 times slowly

Cleaning Code (2 different solution) #

Unlink description
Solution 1 #

Short press “SET” 1 time, short press “ I ” 5 times within 3 seconds

Unlink description
Solution 2 #

Power off and power on, short press “ I ” 5 times within 3 seconds

Cleaning code is done if the light flashes 6 times quickly.

Dynamic Mode List (For remote control only) #

Attention: brightness, saturation and speed are dimmable

No.Dynamic mode
1Automatical color changing
2RGB gradual changing
3Color changing randomly
4Seven color jumping
5Color jumping randomly
6Volcano red
7Forest green
8Ocean blue

9

Three color jumping and gradual changing

Mini Brightness #

  1. Long press “ ” or “ ” in group zone 6 seconds until light flashes one time.
  2. Short press “  ” or “  ” in group zone to set up 10 kinds of brightness level ( 1%, 5%, 10%, 15%, 20%, 25%, 30%, 35%, 40%, 50%).

  Short press any button except “OFF” to confirm or step out setting, the master “OFF”can set up all features.

ON/OFF Time #

The light status changes gradually (factory default time is 0.5s).

1.5s: Short press “ON” 1 times and short press “OFF” 5 times within 3 seconds, the setting is done once light flashes 2 times slowly.

0.5s: Short press “OFF” 1 times and short press “ON” 5 times within 3 seconds, the setting is done once light flashes 2 times quickly.

Music Mode #

Enter into music mode: Long press “M” button on remote until light flashes green color one time

Move out music mode: Long press “M” button on remote until light flashes red color two times

Warm Tips: 

  1. Don’t block out the micro hole on controller.
  2. Don’t install it into sealed junction box.

Attention #

  1. Please cut off power before wiring device
  2. Please check the voltage of power adapter before connecting
  3. Don’t disassemble it if you are not expert
  4. Don’t use it in metallic or magnetic area
滚动至顶部